Step Tutorial for Installing a Bathtub
Step Tutorial for Installing a Bathtub
Blog Article
Are you currently searching for ideas around How to Install a Bathtub Yourself?
Mounting a bath tub isn't specifically brain surgery, but it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably difficult project. If the old tub is readily obtainable, the job can relocate speedily; if you have to open up a wall to remove the old tub and also position the brand-new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and set in the brand-new one. Make sure you have certified on your own for the task as well as fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed task, it is much better to consider employing one before you start. Possibilities are you may need an expert plumber to make tube connections.
This write-up will assist you install a brand-new bath tub in your restroom if you have currently acquired a new bathtub and also don't need to change the arrangement of your previous water pipelines.
Your devices as well as material checklist should consist of the following:
Planning for the Setup
To start with, the supporting frame supplied with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the versatile tap ports to the bottom of both taps using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is detach the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Prior to carrying on to fit the new taps, compare the pipe links on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Making use of the two wooden boards under its feet, position the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by checking the level and adjusting the feet on the bathtub until the level reads degree.
To set up faucets, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression join; then do the same for the other tap.
Switch on the water system and also examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bathtub and additionally examine the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, take care of the bath paneling as explained in the supplier's user's manual. Tiling and securing around the tub must wait up until the bath tub has been utilized at least once as this will certainly resolve it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washers remain in area in between the tap as well as the sink. Protect the tap in position with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind must be linked to the faucet finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a rigid seal, triggering the water to pass through the wall between the bathroom and also the tiling, bring about problems with dampness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components and fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split rather early if you do not consider this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily available on the market. It is recommended to fit the tiles using waterproof or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about Installing A Bathtub, I imagined sharing that excerpt was really useful. Sharing is caring. Helping people is fun. I enjoy reading our article about Installing A Bathtub.
Don't delay, ring today! Report this page